Bluebell Railway Atlantic Group
2010 progress
Thanks to Neil Hunt of Boro Foundry in Stourbridge we have these photos of progress on the rods and axle-boxes.The first photo of an axle-box shows the "rough" concentric ring finish to provide a key for the white-metal surface that faces towards the back of the wheel. This was taken just before Christmas. The other photo of the axleboxes was taken on 26 January and shows the smoother inside face.
Below are two photos showing the roughing out of the coupling rods. They are being left for a while in this state to allow them to stabilise dimensionally before moving on to the next machining operation.
Fred Bailey provides this update and photos, showing recent progress. There are also many other new components on order and eagerly awaited!
The first photo above shows the arm for the reverser being machined in Atlantic House. This arm transmits the movement of the nut (part of the screw assembly in the cab) to the lower reach rod.The second photo shows the upper and lower reach rods temporarily in position with the pivot for the lever (not yet made) in between. The round part is a pivot point for part of the drain cock linkage.
The next photo shows the finishing of the bolts for the air brake cylinders. As can be seen these have a narrow rounded head because there is insufficient room around the bolt hole for a normal bolt head. This detail is taken from the original drawings - not something we have dreamt up!The two main 13" brake cylinders are now mounted on their cross stretcher. The special bolts are those around the top edge (in this view) of the cylinders.
The two photos above show the the leaf springs for the trailing axle (left) and the leading driving axle (right) recently arrived from our supplier. Note also that the grey undercoat is creeping forward.
Take a good look at the photo on the right - this is the last time this will be seen! You are looking inside the steam chest assembly. At the top with an 'A' on it and the bottom with an 'F' are the steam chests proper, where the steam arrives having come from the boiler through the regulator. After passing the piston valve and pushing the piston in the cylinder it comes out past the same valve on route to the blastpipe and chimney. The area between the rounded valve chests is where the exhaust steam arrives. The quarter round tubes help 'streamline' the passage-way and the divider plate crossing left to right prevents the exhaust from one cylinder trying to go into the port for the opposite cylinder. The lid is now welded over all of this. We painted arrows inside to tell the steam which way to go!
This report, illustrated by Fred Bailey's photos, shows recent progress with many new components having been completed in the workshop, or delivered from external contractors.Fresh from I. Riley's we now have the brand new wheels, axles and tyres ready for fitting to the bogie, and the wheelset for the trailing axle. The trailing wheels are actually from an S15 tender, which are of the correct size, number of spokes etc. and are fitted onto a new axle.
Below are the bogie swing link pins - the longer ones are 25" long and are within 3 thousands of an inch of parallel along the whole length, without making any adjustments to the lathe tailstock. This is more than adequate to do the job required.The bronze item is the oil tray for the driving axlebox. The ones for the coupled wheels are well advanced, and these will be finished to fit the axleboxes once they are received.
These next items are the bearings for the weigh shaft (right), together with the weigh shaft clutch below. Note the genuine "Brighton" oil box lids!
The weigh shaft is attached via the reach rods to the reverser in the cab, and via the lifting links to the expansion link of the Stephenson's valve gear.
The clutch is used to steady the shaft and to stop the reach rods and the reversing screw from taking any of the stresses produced by the movement of the valve gear components when the engine is in motion.
On the left is a photo of one of the finished cylinders, now awaiting heat treatment.
The remaining photos below are of the latest castings received on 16th October from Cerdic Foundry.
The first two show the tender water filler casting and a sandbox casting.
... and finally the reverser body, and the front and rear valve chest covers.
A fund raising appeal for the cash required to complete the project was launched in 2000, and a combination of gifts made via the Bluebell Railway Trust, and standing orders set up to provide a steady income to the project have now made over a third of the total available. Whilst this has provided funding for the present work, more is going to be needed to complete the project, and the best way in which you can help is by setting up a small, regular, standing order to the Bluebell Railway Trust under Gift Aid, since this enables the Trust to reclaim the basic rate tax you have paid, and (if you are a higher rate tax-payer) enables you to reclaim some tax as well.
A combined Donation, GiftAid and Standing Order form is available as a pdf document.
For further details contact David Jones.
A donation is made to this project when you buy Historical Transport Film videos from Beulah.
Photos and reports from Fred Bailey.
